| Experimental and numerical assessment of subsurface plastic deformation induced by OFHC copper machining JC Outeiro, S Campocasso, LA Denguir, G Fromentin, V Vignal, ... CIRP Annals 64 (1), 53-56, 2015 | 59 | 2015 |
| A physical-based constitutive model for surface integrity prediction in machining of OFHC copper LA Denguir, JC Outeiro, G Fromentin, V Vignal, R Besnard Journal of Materials Processing Technology 248, 143-160, 2017 | 43 | 2017 |
| Orthogonal cutting simulation of OFHC copper using a new constitutive model considering the state of stress and the microstructure effects LA Denguir, JC Outeiro, G Fromentin, V Vignal, R Besnard Procedia cIRP 46, 238-241, 2016 | 27 | 2016 |
| Friction model for tool/work material contact applied to surface integrity prediction in orthogonal cutting simulation LA Denguir, JC Outeiro, J Rech, G Fromentin, V Vignal, R Besnard Procedia CIRP 58, 578-583, 2017 | 15 | 2017 |
| Residual stresses prediction in machining of Inconel 718 superalloy using a constitutive model considering the state of stress JCO F.A.V.da Silva, L.A.Denguir Procedia CIRP 87, 527-532, 2020 | 13 | 2020 |
| Constitutive model incorporating the strain-rate and state of stress effects for machining simulation of titanium alloy Ti6Al4V W Cheng, J Outeiro, JP Costes, R M’saoubi, H Karaouni, L Denguir, ... Procedia CIRP 77, 344-347, 2018 | 13 | 2018 |
| Influence of cutting process mechanics on surface integrity and electrochemical behavior of OFHC copper L Denguir, J Outeiro, G Fromentin, V Vignal, R Besnard Procedia CIRP 13, 186-191, 2014 | 6 | 2014 |
| Flank wear prediction in milling AISI 4140 based on cutting forces PCA for different cutting edge preparations LA Denguir, A Besnard, G Fromentin, G Poulachon, X Zhu International Journal of Machining and Machinability of Materials 18 (3 …, 2016 | 4 | 2016 |
| Multi-physical analysis of the electrochemical behaviour of OFHC copper surfaces obtained by orthogonal cutting LA Denguir, JC Outeiro, G Fromentin Corrosion Engineering Science and Technology 55 (7), 2020 | 3 | 2020 |
| Caractérisation et modélisation de l'état mécanique et microstructural des sous-couches affectées par l'usinage de finition du cuivre Cu-c2 et impact sur la résistance à la … L Denguir Ecole nationale supérieure d'arts et métiers-ENSAM, 2016 | 2 | 2016 |
| Tribological Analysis of Several Coatings under Flood and Cryogenic Cooling Conditions Y Zhang, JC Outeiro, C Nouveau, B Marcon, LA Denguir Applied Science 13 (21), 11743, 2023 | | 2023 |
| Non Traditional Machining Processes - Part 1: an introduction LA Denguir Knowledge and Skills (ISSN 2800-2083), 010001, 2021 | | 2021 |
| Non Traditional Machining Processes - Part 2: chemical, electrochemical and mechanical processes LA Denguir Knowledge and Skills (ISSN 2800-2083), 010002, 2021 | | 2021 |
| Caractérisation et modélisation de l'intégrité de surface induite par usinage L Denguir Editions Universitaires Européennes, 2020 | | 2020 |
| Comparison of Different Chip Formation Simulation Techniques and Constitutive Models of Ti6Al4V Alloy S. DEHEN, F. DA SILVA, L.A. DENGUIR, J.C. OUTEIRO, F. ZANGER, V. SCHULZE European congress and exhibition on advanced materials and processes …, 2019 | | 2019 |
| “Improvement of surface integrity prediction in machining of Inconel 718 by using a material constitutive model considering the state of stress” denguir l.a. da silva f., outeiro j.c. EUROMAT- Stockholm, Sweeden, 2019 | | 2019 |
| On the optimization of the cutting conditions for an improved corrosion resistance of OFHC copper LA Denguir, JC Outeiro, V Vignal, G Fromentin, R Besnard Procedia CIRP 77, 413-416, 2018 | | 2018 |
Guillaume FROMENTINArts et Metiers - Institute of TechnologyAdresse e-mail validée de ensam.eu
